3D Printing – Lannix Design

Design For 3D Printing – CAD Tips

Nick — Tue, 02 May 2023 21:30:06 +0000

As 3D printing becomes more and more popular, it’s important to keep in mind some key design considerations that are specific to CAD when designing for 3D printing. In this blog post, we’ll go over some of the most important things to keep in mind when designing for 3D printing.

Wall Thickness and Material

When designing for 3D printing, it’s important to keep in mind the wall thickness and the material that you’ll be using. The wall thickness should be at least 0.8 mm in order for the object to be strong enough. The distance between walls must be between 0.4 mm and 0.8 mm, otherwise, the walls will collapse or the object will be brittle.

The filament spool storage tower was designed using the concepts described. Some out-of-the-box thinking was needed to pull it off.

Consider Orientation and Support Structures

When you design a 3D printing model, you need to think about the orientation of the model as well as the support structure for that model. The orientation or direction of printing allows for the right layer strength and adhesion. Support structures can be used to avoid issues that may arise in the printing process. This will help increase the strength and durability of the finished product, and will ensure that the print runs successfully without any issues. Well-spaced support structures can also help speed up the printing process, allowing you to create your 3D designs faster.

Use CAD Software that can Handle 3D Printing

When designing for 3D printing, it’s essential to use CAD software that can handle 3D printing. This software can help you create models that can quickly be printed with accuracy required for 3D printing. The best CAD software will allow you to create intricate designs with precision, and give you the ability to make adjustments and edits when necessary. I recommend Fusion 360 or Onshape for the hobbyist.

Choose the Right Printing Process

There are various types of 3D printing processes available, and you’ll want to choose one that is best suited to your needs. You can choose between Fused Filament Fabrication (FFF), Stereo Lithography (SLA) and Digital Light Processing (DLP). Each process has its own advantages and disadvantages, and it’s important to choose the right one based on your specific design requirements.

The plastic parts in our end table design needed to be easily 3D printed and maintain the angle and position of the timber legs.

Consider the Printing Material

The type of material you select for 3D printing is an important consideration when designing for 3D printing. The material will impact the quality of the final product, and you should choose a material that is strong and durable enough for your needs. Some materials are also more resistant to wear and tear, and those could be a better fit for certain applications.

Final Thoughts

Designing for 3D printing requires a specific set of skills and knowledge. By keeping these considerations in mind, you can ensure that your CAD designs are optimized for 3D printing, and that your finished product is of high quality and meets the desired standards. With the right software, materials, and processes, you’ll be able to create stunning 3D models that meet all of your design needs.

Gallery - CAD For 3D Printing

See more of our work

3D Printer Emissions

Nick — Tue, 11 Apr 2023 21:30:20 +0000

Since the birth of my son I have been increasingly concerned about the release of toxic fumes while our 3D printers are running. Those who have read our blog posts on building our 3D printing enclosures will have seen the ducting system that was designed and 3D printed for it.

While that system works reasonably well, it is not perfect and occasionally the faint smell of the fumes can be detected. I’ve come to realise that the blast doors implemented in the system are ok for dust collection where larger particles are involved but are not ideal for extracting fumes. The lack of airtight sealing around them leads to fumes escaping.

I recently came across this document from UltiMaker that outlines the most effective ways to extract fumes from their 3D printers and it’s given me some helpful ideas on how to improve our current system.

If you’re interested in dealing with 3D printer emissions yourself follow the link below to read Ultimaker’s guide.

Link here.

The current air filtration system in our 4 printer cabinet.

See more of our work

The Benchy

Nick — Tue, 28 Feb 2023 21:30:07 +0000

Even if you’re not into 3D printing you may have seen the little boat model that everyone seems to print. It is called the benchy and while it is a neat little boat, it is actually used to help calibrate a 3D printer since the design incorporates a lot of geometry that tells you if you have your print settings tuned in correctly.

There are many models available that are designed to aid printer calibration but the benchy remains the go-to for most as it looks pretty cool when done and can be displayed on your shelf after use. I have decided to use it to show customers the range of colours available since it doesn’t use a lot of filament.

Check out the video link here to learn more if you’re interested since Michael from Teaching Tech does a much better job at selling the virtues of the benchy than I could!

More next week.

Check out the link from Teaching Tech

See more of our work

We Are Australian Made & Owned

Nick — Tue, 07 Feb 2023 21:30:37 +0000

If you need CAD work, 3D printed parts or both, we can help. We can supply vector graphics files for laser cutting and engineering diagrams for your project. All of our 3D printed parts are produced using Australian made filament. Let us know how we can help you today!

See more of our work

Recycling 3D Printing Filament

Nick — Tue, 22 Nov 2022 21:30:06 +0000

This week we have only a small update since renovations to the new house are taking up most of our time. Something I’ve been interested in personally is recycling wasted filament from failed prints and support material. I thought I’d share some of the options available and what others have been doing.

I found this interesting video from Michael at Teaching Tech on YouTube showcasing a filament recycling machine from Australian company Polylab.

Enjoy!

Teaching Tech’s video on recycling 3D printer filament.

See more of our work

The Road To 3D Printing Success

Nick — Tue, 19 Jul 2022 21:30:06 +0000

Starting out in 3D printing can be a disheartening experience for some people. The lure of the cheap 3D printer can definitely be a trap for new players. In 2016 the M3D was $500 and was one of the cheapest available. Reviews at the time were good but unfortunately it didn’t really live up to expectations.

This blog is the Lannix Design guide to 3D printing built from information I’ve acquired over time. Topics are to do with 3D printer tuning and setup which is enough for one blog post. Slicer settings are another topic which will be covered at a later date.

A cheaper Creality CR10 next to the more expensive but more reliable Prusa i3 MK3S+.

Choose wisely

Nowadays the Creality Ender 3 can be yours for about $350 and is not a bad machine for the money but does require some fine-tuning to get it working well. I acquired some of these after getting my first Prusas and I found the user-friendly experience of owning the Prusas to be very helpful when fine tuning the Ender 3s.

Moving up to a more expensive but far more reliable machine can improve your outlook on life quite a bit. Enter the Prusa MK3S. Even in kit form it is more than three times the price of the Ender 3 but in terms of quality, design and customer experience it doesn’t come close. I’d especially recommend the kit version as it is significantly cheaper in both the initial purchase and import duty (don’t forget that!) and allows you to become more familiar with the machine itself.

I bought my first Prusa in 2019 and built it in the workshop under the house. It showed decent results straight out of the box but as the weather became cooler coming up to Autumn, I noticed that I was seeing more failures. The downstairs workshop is not fully enclosed and I realised that having the printer out in the open was likely the cause of the failures.

Get an enclosure!

Out in the open is usually where people will first set up their 3D printer. This can be ok if it’s in a room with relatively stable humidity and temperature but most people will have it in the garage or a spare room that may have drafts and require you to leave a window open to deal with the fumes.

I noticed a drastic improvement in the quality and consistency of my 3D prints when I started using my custom designed and built enclosure. The advantage of an enclosure is that the humidity and temperature are able to be controlled.

All filaments benefit from a warmer environment and the small volume of air in the enclosure is able to be heated more efficiently than an entire room. Keeping temperatures in the enclosure around 40°C is optimal and also easily achievable since the 3D printer will do this while it is operating.

When using filaments like Nylon, Carbon fibre and ABS/ASA which emit toxic fumes, an enclosure is absolutely necessary. A carbon HEPA filter and supporting ducting is required to deal with these fumes.

Other add-ons like a dehumidifier and custom lighting will also make your 3D printing experience a lot better.

An enclosure doesn’t have to be a custom designed and built project like the ones we have at Lannix Design. 3D printer manufacturers such as Prusa and Creality are now starting to offer enclosures that are designed to fit their own products.

Cheaper alternatives are also available such as a converted photographic tent for around $20 or the popular Ikea Lack table conversion that is a fun and useful project when you first get your 3D printer.

Check out our enclosure blog posts here or hit the buttons below.

The prints don't stick to the plate!

One of the most common and most catastrophic failures is when the part being printed doesn’t stick to the print plate. This is usually caused by a dirty bed plate. Most people will tell you to use isopropyl alcohol to clean the bed but I’ve found this to be unreliable. Washing the plate under hot water with dishwashing liquid will be far more effective.

Another cause of this problem is a variance in temperature in the print area. A sudden draft of cool air across the build plate can cause the part to contract and lose adhesion. An enclosure will eliminate this problem.

Part orientation is also a factor for taller prints. The momentum of the part when the Y-axis is thrusting back and forth can cause it to dislodge.

In extreme circumstances where the above solutions just don’t work for you, applying glue stick on the plate before heating will usually solve the problem.

BONUS – A glue stick is also helpful when printing with PETG which tends to stick too well to the plate. A barrier of glue stick can help since in some instances PETG will damage the plate surface when removing the part.

My part looks so ugly!

Strange looking parts with unexpected lumps and/or holes can be a less than desirable result. There are a few main causes that can be addressed to achieve a better looking part.

Under-extrusion may be caused by a partially blocked nozzle and will result in holes in your print as seen in the fox below. A blocked nozzle can be cleaned out using the cold-pull method. You may have received an acupuncture needle with your printer and wondered what it was for! Now’s your chance to use it.

Cold-pull

Steps to perform a cold-pull to unclog your nozzle.

Disable the stepper motors.
With the filament still in the extruder, heat it up to about 30°C more than the recommended temperature for your filament (ie. 250-260°C for PLA).
Poke your acupuncture needle up into the tiny opening of the nozzle. The idea is to dislodge any debris caught in the extruder such as dirt, crusty old filament and/or metal particles.
After 5 minutes allow the hotend to cool down to room temperature. Turn the extruder fan to full blast to speed this up.
Once the hotend has cooled, heat the extruder back up to around 105°C for PLA.
Allow the temperature to stabilize for about a minute and carefully use your pliers to pull the filament out of the extruder. If you go too hard and snap the filament you’ll need to pull the hotend assembly apart to get it out.

It may be necessary to repeat the process to fully remove the clog.

Other problems with the appearance of the print such as ‘zits’ and ringing can be cured in the slicer software and will be covered in a future blog post. Keep updated with our monthly newsletter.

Strange looking part finish caused by under-extrusion.

Filament has snapped inside the extruder. Likely caused by a clog in the nozzle.

It only printed half of the part!

If your printer says it’s finished printing your part but it’s missing some of the top layers, it may mean that the filament has snapped off in the extruder and/or that it has become stuck when entering the extruder assembly.

In the case of the Prusa MK3S it has a filament detector in the top of the extruder assembly. This works well for the most part but in the case that the filament becomes stuck in the lower extruder, it cannot detect anything wrong.

Snapped filament

Snapped filament happens when the extruder is fully clogged and won’t allow the gears to push any more material through. The gears wear away at the filament which eventually breaks it.

Performing a cold-pull may take the blockage away but it is likely necessary to pull the extruder assembly apart to get to the filament. Any filament particles will also need to be cleaned out using compressed air. In extreme cases it may be necessary to pull the PTFE tube out of the hotend to get the foreign particles out of the nozzle.

Stuck filament

It is sometimes difficult to tell if the issue is caused by a clogged nozzle or not. In rare cases it can be a case of bad filament. It is becoming a rare occurrence these days with filament quality improving across all manufacturers but defects happen. The above photo shows an impurity that caused the printer to stop extruding because the filament was too thick to pull into the extruder.

The manufacturer has generously replaced the entire reel free of charge.

Inconsistent filament cross-section caused by manufacturing defects.

What's this huge blob on the nozzle?

A large blob of filament on the nozzle is caused by either a buildup of schmutz on the underside of the extruder or a partially block nozzle.

If you have a blob formed on your nozzle DO NOT try to remove it while the hotend is cold! You will break the wires on your thermistor which means you will either have to rewire it or replace it! Ask me how I know… If you’ve already broken your thermistor, we have a guide to replacing it in a Crealtiy CR10 here.

The blob of death kills your prints.

Buildup

Debris will acquire on the underside of the hotend due to slight defects in the filament material and a lack of cleaning. Once the buildup becomes significant enough, it will catch the part being printed and bring it with the extruder assembly. From that point on the extruder will keep pumping filament into the part creating the dreaded blob of death.

This can be prevented by keeping the nozzle and heat block clean by lightly scrubbing with a brass brush while the hotend is heated.

Partially clogged nozzle

A partially clogged nozzle will allow filament through the opening of the nozzle but has the characteristic of curling up on the way out. The extruded filament should always come straight down out of the nozzle.

If the curling becomes too severe, the filament will eventually stick itself up under the heat block and drag all subsequent filament along with it which is when the blob starts forming. This clogging can be fixed using the cold-pull technique mentioned above.

Conclusion

Wow, this post was meant to be a short one since I have to get the newsletter out this week!

I hope this has been helpful to you if you’ve just started out or are thinking about getting into 3D printing. I enjoy putting out content like this and if you have any questions I’m happy to answer via email or Facebook messenger.

If you’d like to see more or keep informed when future blog posts come out, please subscribe to our monthly newsletter below.

Ciao!

Gallery - 3D printing problems and solutions

See more of our work

December 2021 – Downloading models for 3D printing

Nick — Thu, 09 Dec 2021 21:30:05 +0000

People often talk to me about 3D printing and are fascinated by the process. To some it seems like only nerds can do it and that is certainly true to some extent! You don’t need to be an expert in computers and CAD to find something to interesting to 3D print.

There are many website around that offer free to download 3D models that you can 3D print yourself or can have us 3D print for you here at Lannix 3D.

An older relative of mine said he reckons 3D printing is just making little plastic knick-knacks but that is far from the truth. We have endeavoured to showcase some of the useful objects that can be produced with 3D printing and aim to introduce to many the advantages of having a 3D printer. We believe in future, having a 3D printer in the home or workshop will be as commonplace as having a computer.

The Lannix logo was designed in house but you don’t have to know CAD to have something to 3D print

Just recently, my dad broke some plastic clips in the back of his car seats which had gone brittle over time. 3D modelling them and printing out replacements was a simple job. Check out some of our other blog posts to see some of the handy parts we’ve made using CAD and 3D printing.

But I digress… Check out the websites below for some FREE STUFF!

Websites with free 3D models

Printables.com is the official 3D model sharing site of Prusa Printers. It seems to have higher quality models than most and is the favourite here at Lannix Design!

MakerBot’s Thingiverse is probably the most popular website for 3D model downloads and is setup for 3D printing. All 3D content is free to download.

MyMiniFactory guarantees the models they have are verified to be 3D printable. Most models are free to download but they have recently expanded to include paid content.

Thangs is a compiler for multiple 3D model websites meaning that it will search most of the sites mentioned and display them on the same page for you. It’s a newer site but there’s already heaps of models free to download.

UltiMaker’s YouMagine is a site that has good quality 3D model downloads but not as many as some of the other sites. All 3D content is free to download.

The Smithsonian Institution has 3D scanned a lot of the display items in their museum. They’re kind enough to offer them up on their website for free download.

GrabCAD is more of a resource for engineers to assist with designing new parts that need to interact with existing real-world parts. The models are free to download and are very handy to have in your design kit.

Websites with 3D models worth paying for!

3D sets have designed the Landrover model that we have produced along with some other RC vehicles. The amount of design work that has gone into creating these vehicles for 3D printing is astounding!

See more of our work

October 2021 – We Use Australian Made Filament

Nick — Thu, 07 Oct 2021 21:30:37 +0000

I’ve been playing with 3D printers since 2016 and in that time I’ve learned that when it comes to 3D printer filament, you get what you pay for! Thankfully in that time, many new companies have come to the market with better and better products.

After a lot of experimentation with filament offerings from various companies, we use Aurarum filaments. They have the best combination of quality and price that we’ve found and the best part is, they’re based in Melbourne, Australia.

They’re not only based in Australia but they manufacture their own filaments on-site in the Victorian warehouse.

The filament works well with our Prusa 3D printers and I must say that the quality is comparable to Prusa’s own high quality filament, the difference being that it is far easier to get hold of here in Australia and is more reasonably priced.

www.aurarum.com.au

Aurarum 3D printer filament

Gallery - Quality prints start with quality filament

See more of our work

April 2021 – The Beginning

Nick — Fri, 09 Apr 2021 21:30:03 +0000

COVID 19 has affected us all in some way. Lannix Design was created in response to the uncertainty that the pandemic has brought with it. The business has been created as a way to turn what was a hobby into a real business.

3D printers can be temperamental and are affected by temperature and humidity fluctuations. In order to make the end product more consistent and of a higher quality, an enclosure is required to insulate the machines from these atmospheric changes.

Stage one of the enclosure’s implementation is now complete and has made a huge difference to print quality. Check out some of the images below which include some 3D printed templates and brackets that aided in the construction of the enclosure.

Future additions to this project will include an air filtration system governed by a microcontroller. This will allow the use of filaments which emit unpleasant fumes, which will be captured in activated carbon and HEPA filters.

Design concept – 3D printer enclosure/laser cutter bench

Gallery - 3D printed parts to make 3D printed parts!

See more of our work

March 2021 – Conception

Nick — Mon, 15 Mar 2021 21:30:46 +0000

It’s time to turn this side hustle into a legitimate business! This taste of independence has fuelled a desire to have a go at making a proper living from this. I have the knowledge and experience to consider myself more than capable of taking it to the next level so here it is.

This month has been spent setting up the admin side of things properly, registering as a real business and getting my hands on a few more machines, and getting them ready to get to work.

I never imagined it would take so much time but I guess when I think about it, I am doing the jobs of many people at once, from director to accountant to floor sweeper upper…

Thanks to all the people who have encouraged me to make a go of this; my partner Jade, my friend and mentor, Capper and my family.

Cheers!

3D printers can be quite finicky. It takes a lot of fine tuning to get them to the point now where they produce reliable results.

3D Printing – Lannix Design

Design For 3D Printing – CAD Tips

Wall Thickness and Material

Consider Orientation and Support Structures

Use CAD Software that can Handle 3D Printing

Choose the Right Printing Process

Consider the Printing Material

Final Thoughts

Gallery - CAD For 3D Printing

See more of our work

3D Printer Emissions

See more of our work

The Benchy

See more of our work

We Are Australian Made & Owned

See more of our work

Recycling 3D Printing Filament

See more of our work

The Road To 3D Printing Success

Choose wisely

Get an enclosure!

The prints don't stick to the plate!

My part looks so ugly!

Cold-pull

It only printed half of the part!

Snapped filament

Stuck filament

What's this huge blob on the nozzle?

Buildup

Partially clogged nozzle

Conclusion

Gallery - 3D printing problems and solutions

See more of our work

December 2021 – Downloading models for 3D printing

Websites with free 3D models

Websites with 3D models worth paying for!

See more of our work

October 2021 – We Use Australian Made Filament

Gallery - Quality prints start with quality filament

See more of our work

April 2021 – The Beginning

Gallery - 3D printed parts to make 3D printed parts!

See more of our work

March 2021 – Conception

Gallery - The evolution of the Lannix Design logo

See more of our work